- 0
Slow Programme Guide
-
Similar Topics
-
By northshields
I have a 32LQ63 model and had always thought that I should be able to watch catch-up tv from the previous 7 days direct from the epg.
However, I cannot for the life of me get that to work. Whatever I do, whenever I am in the epg I can only get it to move forwards rather than back. I can watch catch-up tv from Freeview Channel 100, but I would like to be able to do so from the epg. What am I missing?
-
By NickL
Hi,
I recently bought an LG UK6500PLA TV (my first LG), but I have a difficult time streaming content (Wifi connected), e.g. Netflix series is streaming in low resolution. The router is only 10 feet away from TV (but ethernet is not an option) and uses a 5GH frequency range.
I have tried making a speed test at fast.com, for both the TV (through the Webbrowser) and for my laptop and iPhone. The speed test for TV showed 2.5 Mbps and my laptop and iPhone showed 110 Mbps. Can there really be such a big difference? I am starting to wonder if this might be a warranty issue?
Do any of you guys have experience with bad Wifi reception on your LG TV or have any suggestions on how to fix it?
Br,
Nick
-
By Mandx
I have recently bought a 48 inch lg oled. For some reason I am getting super slow internet speeds no faster than 10 megabits at the tv even though I have Fiber internet. I have it directly connected with cat 5 Ethernet cable to my Internet providers gateway. I tested the same cable and port with other devices and I am getting near 1 gig of speed. What gives
-
By Peter_T
LG Oled42c44LA; cable TV to CI+ module
Program guide works OK until ca. 17.30-18.00 . Then the guide only shows current programs. Inspecting later times is not possible. Only thing that helps is to unplug the TV and plug it in again. But the next day the problem is there again around the same time. Is this a problem of the LG TV? Is there a solution for this?
-
-
By pivotCE
I’m pretty sure it’s safe to say there are more HP TouchPads left in the world than there are their matching original barrel chargers. This means if you have a TouchPad today, you’re probably using a TouchStone, a computer, or any other random USB A charging brick to (very slowly) charge your 13 year old device. And it means you’ve seen the error message in the image above every time you’ve plugged it into anything other than the original barrel charger or a computer. Fun fact, you can trick the TouchPad into charging normally and not feeding you the message by creating your own custom micro USB or USB C cable if you’ve
link hidden, please login to view. Stuff You’ll Need
Assuming you have a micro USB (ie. non USB C modified TouchPad) you’ll need:
1. A 4-wire micro USB to USB A cable
2. and 1/4 watt resistors (1 each per cable)
3. Soldering iron and solder
4. Heat shrink or electrical tape
If you’re making a USB C cable but only want to use it with a USB A charger then you’ll need:
1. A 4 wire USB C to USB A cable
2. Items 2-4 above
If you’re making a true USB C to USB C cable that you plan to use with a USB C 3.1 charger you’ll need:
1.
2.
3. Any 2-wire cable or a 4-wire cable that you’ll cut the data wires out of (green and white typically) and that you’ll cut the ends from
4. Items 2-4 from the first section above
Prepare the Wires
Regardless of which cable you’re making, the end that goes to the TouchPad will need all 4 wires and the resistors. So grab the 4-wire cable of your choice and strip the ends, and I recommend pre-tinning them with some solder.
Build the TouchPad Side of the Cable
See the image below for how to arrange the resistors. If you’re making a USB A cable, go ahead and cut into two pieces, set aside the USB A side, and grab the micro or USB C for this part.. It doesn’t matter how far away from either end you go, it’s your choice. Strip the wires back so you have enough bare wire to work with.
1. Solder the ground (black) wire to one side of the 300k resistor.
2. Solder data- (green), data+ (white), the other side of the 300k resistor and one side of the 250k resistor together.
3. Then solder the other end of the 250k resistor to the red (power) wire.
Build the Charger Side of the Cable
If you’re making a USB A cable, then all you have left to do is reconnect power (red) and ground (black) to their corresponding colors on the TouchPad side of the cable, trim off the data lines from the USB A side, clean it all up with some heat shrink or electrical tape and you’re done!
If you’re making a USB C to USB C cable grab the USB C board I linked above and your 2-wire cable (or 4-wire that you’ve trimmed the data lines from). You’ll also have to cut the end off to make room for the new connector.
1. Pre-tin the board on the two outside pads marked as VCC and Gnd in the image below.
2. Solder on the red (power) wire to VCC and then black (ground) to Gnd. If you bought the housing and boards together, don’t forget to the housing on the wire before you start soldering. You also may need some super glue to keep the plastic housing from coming apart.
3. Back at the TouchPad side of the wire, take the other end of your 2-wire cable and attach red and black to their corresponding ends, clean it up with some heat shrink or electrical tape and you’re done!
Final Thoughts
You should now be able to use any charger you want to and the TouchPad will believe you’re plugged into a normal battery charger and will allow the normal charge rate flow through.
Note, you’ve effectively removed the ability to use this cable for Data since the data lines are no longer connected.
Also, for those who modded the TouchPad with USB C, the port already has 5.1k resistance but cannot communicate that to a USB C 3.1 charger with the added resistance on the data lines. This is why the TouchPad end of the USB C cable must be a “dumb” 4-wire USB C cable and the charger end needs the 5.1k resistance to tell the charger on that end to send power. This also means that you must remember which end is which, but don’t worry. Picking the wrong direction won’t hurt anything as the USB C charger won’t allow power since the wire doesn’t tell it to. I marked the TouchPad side of the USB C cable with a dab of orange paint pen.
Finally, I hope you found this helpful or at the very least entertaining! I had fun exploring the different ways of making this work and so feel free to give it a watch.
#webos4ever
The post first appeared on . Related posts:
-
-
Similar Tagged Content
-
- 0 replies
- 1,115 views
-
- 1 answer
- 10,120 views
-
- 0 replies
- 4,592 views
-
Questions about LG Web OS Smart TV and Dish TV Set Top Box
By AnonViewer,
- stb
- mychannels
- (and 2 more)
- 14 answers
- 11,958 views
-
Question
Den C
LG50UK6950. The programme guide is slow to load, and has to re-load for each page. My previous LG tv (a 49UK.....) was the same.
Samsung, Panasonic, Toshiba and Sony are almost instantaneous.
Is this a hardware problem, eg lack of memory, or software - in which case is it ever going to be fixed?
24 answers to this question
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.