Quantcast
Jump to content

Join Amazon Prime - Watch Thousands of Movies & TV Shows Anytime - Start Free Trial Now ×

Lag/buffring when Streaming from NAS

showkatl
 Share

Recommended Posts

showkatl Rookie

showkatl

Posted
Posted

Hi,

I have recently purchased LG 32LH602D TV which has WebOS3 Version 03.20.08. I usually stream Pictures/ Audio/Video from my WD NAS drive. Previously i had Samsung Smart TV and streaming has never been any issue. Now setup is same only change is Samsung has been replaced by LG TV and I am facing issue streaming, Pictures take lot of time to buffer/ videos take time initially to buffer and then again stop in between to buffer. Spoke to some local LG technicians without any help. Is there any know issue. I do see lot of lag even while changing menus like settings on TV.  

I am using LG Photo & Video app to stream, been reading Plex availability in LG store but I don’t find it there,… is it available or removed?

 

My setup is .

 

NAS connected to router via LAN cable / TV connected to same router via LAN cable ( tested Wifi as well but same issue)

 

My all other devices can stream from same NAS device without any issue Wifi or LAN  

 

​Any help will be appreciated.

 

​

​Cheers

Showkat

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Jibun no Kage
      Wake on LAN only works for a few minutes after TV is turned off?
      By Jibun no Kage
      Asking this hear, since I could not seem to find a better place... Wake on LAN only works for a few minutes after TV is turned off?  If I turn of LG TV (WebOS 8.x) and then send a Wake on LAN (WoL) packet, it works.  If turn off the LG TV, then I wait about 15 minutes or so, then send the same WoL sequence, using the same code, script, etc., it fails, the LG TV never turns on.  THe LG TV is configured both for wired ethernet (preferred) and WiFi.  Any idea why this behavior?  It almost seems like the LG TV goes into standby, via phone app, remote, even CEC, etc., then drops from the network?  Mobile is enabled on the TV, hence the phone app works.  Why would the LG TV stop responding to WoL packets?
    • Mike_S
      Smart Remote
      By Mike_S
      Smart remote constantly disconnects. I’ve pushed home and back button and when trying to setup remote receive error message “Bluetooth service needs to be inialized”
      Ive tried everything suggested on the internet to include turning off tv waiting 15,30,60 seconds and trying again. Eventually it will reset up but then will will disconnect. Extremely frustrating and tv is really unusable when this happens. The worst is getting into a streaming app and the remote fails and can’t get out without turning tv off. I would list tv model # but since I started this message remote has disconnected again. Help very much appreciated 
      thx
    • Maria D
      Change view from 16:9 in movies to fit full screen - LG QLED B22
      By Maria D
      How to change view from 16:9 in movies to fit full screen 
       
      LG QLED B22 
    • Bob17821
      Is there an app for WebOS which determines and displays the speed of the Internet connection?
      By Bob17821
      I have problems with one of my WebOS TVs which looks like a speed problem, but when I do a speed check on my iPhone from just a few feet away the connection speed looks fine.  Thanks,  Bob
    • Get More For Your Device
    • skan
      Has anyone rooted his LG TV to enable DTS audio?
      By skan
      Hello.
       
      Some tutorials explain how to do it. 
      We first need to root the TV with scripts such as RootMyTV, and then install dts_restore. 
      Both tools are free and available at github.  
      I'm not writing the links because I don't know if it's allowed in this forum and because I take no responsibility. 
       
      My question is:
      Has anybody tried this process? Does it work? 
      The documentation says if you have any problem you can just factory reset the TV, but I don't dare to do it. 

WEBOS FORUMS

MORE SECTIONS

FOLLOW US ON

×
×
  • Create New...