-
-
Similar Topics
-
By News Reporter
Company Drives Strategic Growth With AI webOS, an Intelligent Platform
that Delivers Outstanding Customer Value and Unique User Experiences
SEOUL, Sep. 30, 2024 — LG Electronics (LG) last week held webOS Summit 2024 in Incheon, South Korea, sharing its strategic vision and future initiatives for expanding the AI webOS ecosystem and growing its platform business. Themed “Empowering webOS with AI,” the second webOS Summit played host to around 300 attendees representing 140 partner companies – including content developers, producers and providers – from 24 countries. The event also marked a major milestone: the tenth anniversary of the launch of webOS on LG smart TVs.
AI webOS plays a pivotal role in LG’s ambitious business transformation, shifting from a consumer electronics manufacturer to a Smart Life Solution Company. With a strategic investment of over KRW 1 trillion (USD 740 million), LG aims to significantly enhance the capabilities of its webOS platform and related businesses.
To achieve its strategic vision and elevate the value of its unique offerings, LG is continuously broadening the extensive selection of content and services accessible on AI webOS. The platform, which delivers exceptional experiences to LG TV users in over 180 countries, currently provides over 4,000 apps, including those for entertainment, home fitness, education and gaming.
This year, LG is reinforcing the reputation of AI webOS as an advanced gaming platform by adding a variety of new services and experience innovations. At present, the cutting-edge platform offers around 4,500 games across popular cloud gaming services such as GeForce NOW and Amazon Luna. To make gaming on its TVs even more responsive, LG has teamed up with MediaTek and Razer, leveraging new Bluetooth Ultra-Low Latency (BT ULL) technology to reduce input lag to an imperceptible 1ms when using a Bluetooth gaming controller. Demonstrated during webOS Summit 2024, this impressive responsiveness enhances the cloud gaming experience, giving users more precise control and making gameplay more immersive.
LG is also bolstering its competitive edge in content and services by actively seeking out and securing top industry talent. The company recently hosted a global hackathon to discover compelling new games and AI-powered content suitable for AI webOS and is also collaborating on game development with respected institutes of higher education, such as Sungkyunkwan University and New York University.
Furthermore, with the introduction of webOS Pay, LG has made it faster and more convenient for users to purchase content and services on AI webOS. The simple-to-use payment service contributes to the seamless, personalized shopping experience on LG’s intelligent platform.
Over the last decade, LG has sold a remarkable 220 million smart TVs and has consistently strengthened its webOS platform business through licensing agreements with an array of local and global companies. LG first made webOS available to other TV makers in 2021, and since then, the versatile platform has been adopted by over 400 brands. The company is now poised to further expand the webOS ecosystem via an array of webOS-powered automotive infotainment solutions, digital signage, smart monitors, gaming monitors and projectors.
Additionally, the webOS platform is shoring up LG’s strong competitiveness in the advertising business. In 2024, revenue generated by advertising and services on webOS is projected to exceed KRW 1 trillion, which represents a fourfold increase from 2021.
A significant contributor to this excellent performance is LG Channels, a free, ad-supported streaming service that provides over 3,800 channels and is now available in 29 countries. The company has augmented its already stellar offering of top-notch viewing options on its free service with the launch of LG Channels Showcase and LG 1 – new channels boasting a curated selection of premium entertainment. What’s more, LG is adding value to the user experience via the provision of AI-based ad solutions that make content recommendations even more relevant to user preferences.
With its Affectionate Intelligence vision for a more caring, empathetic and attentive AI technology, LG is continuously enriching and enhancing the customer experience. The application of Affectionate Intelligence allows webOS users to enjoy easier control as well as personalized content and service recommendations suited to their individual tastes and lifestyles. Through collaborations with innovative partner companies and the seamless integration of the latest technologies, LG is constantly refining its cutting-edge platform.
Along with informative presentations and demonstrations, webOS Summit 2024 featured an experience zone where attendees were able to see first-hand how powerful AI technologies are driving customer experience innovation on webOS. One of the many intelligent features offered on LG’s platform, AI Concierge employs voice recognition, search history and user data to provide customized app and viewing recommendations. Thanks to its ability to recognize different voices, AI webOS can take each LG smart TV user straight to their own personalized Home Screen without having to manually select their profile.
“Our webOS platform business continues to go from strength to strength based on close collaboration with our valued partners and an unrelenting focus on meeting the diverse needs of our customers,” said Park Hyoung-sei, president of the LG Home Entertainment Company. “Celebrating a decade of webOS innovation, and now enriching customer’s everyday lives with AI webOS, LG is accelerating its transformation into a leading media and entertainment platform company.”
# # #
link hidden, please login to view -
-
By Yves Gijbels
It seems that the latest version of the WebOS browser on LG Smart TV's lacks the support for Javascript modules (ES6).
Can this be implemented / activated?
-
By pivotCE
Well, it’s 2024 and technology continues to advance. The TouchPad isn’t new by any means, but that doesn’t mean it can’t be slightly modernized to be more convenient today. Specifically, it is entirely possible to convert the TouchPad’s Micro USB port to USB C for charging and USB storage access. I’ll show you how.
This is a tough mod which requires micro-soldering and modifying a PCB which you will have a hard time sourcing a replacement for without buying another TouchPad. Proceed at your own peril.
Tools for the Job
To do this mod you’ll need a few things for tools and parts. Here’s a list of what I used:
– Needle nose pliers/tweezers
– USB C boards with 5.1k resistors
link hidden, please login to view
– Soldering iron, solder, flux and a hot air station
– Flush cuts
– Dremel with cutting or sanding wheel
– 28 AWG wire or smaller. 30 AWG is pretty good but any wire around 0.25mm to 0.5mm should work.
– Small file and screwdriver set
– Painter’s and kapton tape
– Metal spudger Disassemble the TouchPad
This is where you’re going to want to get that metal spudger out and be very careful not to snap clips. I can’t explain it better than iFixit already did so go check out their and then come back here.
Modify the USB Connector Board by Removing the Micro Port
There are a few ways to remove the Micro USB port. I added a bunch of flux and coated all the connectors in fresh leaded solder and then used a hot air station set to 800 degrees while wiggling the port very slightly with needle nose pliers. You don’t have to be particularly careful here so if you want to cut the port off with the dremel or the flush cuts or just rip it off with the pliers, (I don’t recommend it but…) that’s fine. We’re not using the pads it’s soldered to anyway. You should STILL be careful not to crack the board. Go slow. Be patient.
Trim the USB C Board
We need to expose the USB C port a bit on this board so let’s cut it down. Grab the painter’s tape and flip the USB C board upside down. You’ll see a small trace between the front and rear anchor points on the right side, which we don’t want to cut. Mark the tape just on the other side of that trace like I did. Dremel along the tape line until you get to the port. You can then use needle nose pliers, a flat file, and/or flush cuts to remove the rest of the board from the bottom of the port.
Prepare the USB Connector Board for the USB C Port
We need to slide the port into the old space so grab the painter’s tape again and mark off the area I marked to make room for the USB C port. You can place the port up to it like I did and use that as a guide. Grab your dremel again or a similar tool and cut out what you marked off. When you’re done, the USB C port should slide easily into the groove. It will fit tighter when we add the kapton tape in a later step.
Make Room in the TouchPad for the Added Thickness of the USB C Board
The USB C board will sit underneath the USB connector board so we have to make room by trimming away the plastic underneath. For this you’ll need to use flush cuts or any other tool you have to chip away. You could use the dremel for this if you’d like. Be careful to not go beyond the first inner layer. Beyond that is the outer shell of the TouchPad. There’s no real method here, just cut out the screw posts and chip away. Use the pictures below as a guide.
Cut the USB C Hole from the Old Micro USB Hole
To open the micro USB hole enough to fit the USB C port, take a rounded file to the left and right of both sides and just file a little bit at at time. Use a small flat file to widen the top and bottom of the port. This process is just trial and error. File a little and then grab the USB C board to test. The port will need to fit inside the hole a bit so you can push it through from the outside to test the hole size if that’s easier. Note: the USB C board will likely not rest on the bottom of the TouchPad and will float a little. This is good because it makes room for your wires and a little kapton tape underneath.
Tape the USB C Board
Since we hacked away at the USB connector board it’s possible we’ve provided the perfect environment for creating shorts! Oh no! So get out the kapton tape because we’re going to add a layer on both sides. You’ll see how I did it on one side below. Do it on both sides. You’ll also notice how I did not cover those two small square contacts just at the bottom of the tape. That’s because we need them.
Where To Get Power and Data
You’ll see the diagrams below which I’ve marked with VBUS (power), data in, data out, and ground. Obviously the old port is gone and most if its pads, but I wanted to show that both sides of the board have the connections. You could possibly do this mod differently, and if you so choose, hopefully these help.
A quick note: this mod can be done with a 4-pin USB C port. That would give you power and data just like with the USB C board I’m using in this guide, however, a 4-pin USB C board will not charge with a USB C charger (ie USB 3.1). The board I’m using in this guide provides the ability to use any charger because it comes pre-built with 5.1k resistors wired to CC1 and CC2 to ground. This is the trick that tells the USB C chargers to send power to the device.
Solder the USB C Board into the USB Connector Board
This isn’t a “how to solder tutorial” so hit up youtube and find a good tutorial that works for you. In general though, use flux, pre-tin the VBUS, Ground, D-, and D+ pads on the USB C board as well as the points on the bottom of the USB connector board.
Now for the tricky part, I didn’t list it in the Tools section above, but it would really help to have magnification or a digital microscope for this. I have these things and I used both. You might have steadier hands and better eyes than me. The picture below was my first attempt of the three TouchPads I modded, and it’s not my best soldering work, but fundamentally, this is what yours should look like.
Put the Pieces Together
You can use a bit of kapton tape to secure the wires in place a bit more if you’d like but it’s not required. It won’t short since it’s only plastic underneath. This is all press fit into place, but if you’re uncomfortable with that, you can add a little hot glue under the board as you put it back into the TouchPad. You don’t have to put the metal shield back into place if you don’t want to. It’s all a pretty tightly fit and if you find the TouchPad screen isn’t as flush as you want, just leave the metal shield off. A little kapton tape right on top would be fine instead.
Congrats, You Now Have USB C
I did this mod on three TouchPads and each one works fine with any USB charger I could find, including USB C port having USB 3.1 chargers. I can also confirm the data connection works just like it should to connect via USB mode on PC. Sadly, this doesn’t do anything to stop webOS from telling you the charger you’re using isn’t the original TouchPad barrel charger, but you can make a custom cable to stop that which I’ll cover in a future article on pivotCE.
#webOS4ever
The post first appeared on . Related posts:
-
By Rizwan Sumra
My LG television does not have a CI Module and pay chennals shows scrambled. In some LG televisions, some free to air channels work fine while others pay chennals will display the message "No CI Module". How to watch other LGTV "Scrambled" channels.
-
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.