Quantcast
Jump to content

PreCentral: Add Pinterest image pinning to your TouchPad with a patch


Recommended Posts

Add Pinterest image pinning to your TouchPad with a patch

We're not entirely onboard with Pinterest's pinboard-inspired photo sharing social network, but we can understand why somebody would be. It seems like it might be fun, you know, if we had anything worth sharing. webOS Nation forum member BeckeyJane found herself wanting better (read: any) Pinterest support for her TouchPad, and she found her savior in fellow member and webOS developer hkowalczyk.

Mr. Kowalczyk just so happens to have a wife who's also an active Pinterest user, so he created a patch to

link hidden, please login to view
in the webOS browser. Essentially it's a bookmarklet that throw's that images URL over to Pinterest for pinning on your pinboard (obviously a Pinterest account is required for this to work and be useful).

The patch is available right now in the webOS Nation forums - just download it on you computer and install with on your TouchPad. It's pinteresting.

mf.gif


a2t.imgtFOEdLKZaGY

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By David Daul
      My magic remote and my Roku remote stopped working for turning off power so I performed a factory reset after troubleshooting to get the remote working.  I am now stuck at the 1st screen of the Factory Reset which says "Press the OK Button(wheel) on your remote."  Well... this really stinks because the remote doesn't work!!!  I have tried a USB mouse, a new magic remote, other LG Remotes with no luck.  I have also tried using the button on the bottom of the tv.  And, I contacted support which was just an exercise in redoing everything I had already tried... No Luck!!
      This is a Nano Cell 55NANO81ANA which is basically just a big brick now since I cannot even use any of the inputs.  Does anyone have a trick for getting past this initial screen???
      Thanks for the help.
    • By News Reporter
      Designed for the Healthcare Sector, Company’s Latest Medical Monitor
      Provides Impressive Imaging and Convenient Features

      SEOUL, Oct. 9, 2024 — LG Electronics (LG) is launching its new 31.5-inch surgical monitor (model 32HR734S) featuring advanced Mini LED display technology. Designed to provide color video displays of images from surgical endoscopes, laparoscopic camera systems and other compatible medical imaging systems, LG’s monitor has received 510(k) clearance from the U.S. FDA, indicating it can now be sold in the U.S. The 32HR734S’s Mini LED technology enables precise brightness control and provides a wide color range, optimizing image clarity and color, making it an ideal choice for a variety of surgical applications, including laparoscopy and endoscopy.
      The 32HR734S features a 31.5-inch, 4K resolution (3,840 x 2,160) Mini-LED display leveraging thousands of tiny LED diodes as the Back Light Unit (BLU). Delivering 2,000 cd/m² peak brightness and a dynamic contrast ratio of 1,000,000:1, LG’s medical monitor leverages 1,536 local dimming zones to produce clear, detailed images and enhanced visual contrast. The display also provides excellent color consistency across the screen and boasts 98 percent coverage of the DCI-P3 color space.
      In addition to its impressive visual performance, the 32HR734S delivers the durability and reliability necessary for surgical settings. Employing Optical Bonding technology, along with Anti-Glare, Anti-Reflection and Anti-Fingerprint coatings on its front, LG’s 32HR734S 4K surgical monitor ensures optimal visibility even in brightly lit operating rooms. What’s more, the front and rear of the product (IP45- and IP32-rated, respectively) offer excellent resistance to water and dust, preventing fluids or particles from disrupting monitor operation during surgeries.
      The 32HR734S is also the first LG surgical monitor to incorporate the innovative Clone Screen feature. Clone Screen allows users to duplicate the image being displayed on the 32HR734S on a second monitor (connected via HDMI), significantly enhancing operational efficiency and communication within the surgical environment, especially in situations where multiple medical professionals need to view the same image.
      For added versatility, the display’s Mirror Mode makes it possible to flip the on-screen image horizontally, while Rotation Mode can rotate the image 180 degrees to match the orientation of the surgical camera. The 32HR734S also provides Picture-in-Picture (PIP) and Picture-by-Picture (PBP) functionality, the latter allowing the display of up to four different image sources simultaneously. This enables medical staff to view a combination of inputs or images, such as laparoscopic and fluoroscopic images, while monitoring the patient’s vital signs at the same time.
      “Featuring advanced Mini LED technology, the 32HR734S delivers the excellent picture quality and convenient functionality needed in surgical settings,” said YS Lee, vice president and head of the IT business unit of LG Business Solutions Company. “We believe our new model will significantly boost efficiency for medical professionals performing and assisting with surgeries.”
      Key Specifications:
      LG Surgical Monitor (32HR734S)
      Size 31.5-inch Backlight Technology Mini LED Screen Resolution 4K (3,840 x 2,160) Display Panel Type IPS Aspect Ratio 16:9 Surface Treatment Protection Glass (Optical Bonding, Anti-Reflection, Anti-Fingerprint, and Anti-Glare) Color Gamut (Typ.) DCI-P3 98% Brightness (Typ.) 800cd/m² Brightness (Stabilization)
      500cd/m² Peak Brightness (Typ.) 2000cd/m² Color Bit 10bit Contrast Ratio (Typ.) 1,000:1 Response Time (Gray-To-Gray)1
      5ms Features DICOM Compliant Yes Hardware Calibration LG Calibration Studio HDR HDR 10, HDR Effect Video Signals Input Terminals HDMI x 1, DisplayPort x 1, SDI (12G / 3G) x 4, DVI-D x 1 Output Terminals HDMI (Clone Screen) x 1, SDI (12G / 3G) x 4 Connectivity USB USB 3.0 1 Upstream, 1 Downstream Power AC Input 100-240Vac, 50/60Hz Power Consumption 130W (Max) / Less than 0.3W (DC Off) Durability IP Resistance Rating2 IP453 (Front), IP324 (Except for Front), IK065 User
      Convenience PBP Yes (2 / 3 / 4 PBP) PIP Yes Screen Flip Mirror Mode, Rotation Mode Failover Input Switch Yes Physical Specifications
      Weight 9.7 kg Wall Mount Size 200 x 100 / 100 x 100 mm # # #
      1 GtG: Gray-to-gray response time.
      2 Tested under controlled laboratory conditions with an IP/ IK rating. Dry before using. Do not charge while wet.
      3 IP45: Protected against solid foreign objects of 1.0 mm and greater / Protected against access to hazardous parts with a wire / Protected against water jets.
      4 IP32: Protected against solid foreign objects of 2.5 mm and greater / Protected against access to hazardous parts with a tool / Protected against vertically falling water drops when enclosure tilted up to 15°.
      5 IK06: Protected against 1-joule impacts.
      *Specifications may vary by region and all features, standards, and other product specifications are subject to change without notice or obligation.

      link hidden, please login to view
    • By pivotCE
      Well, it’s 2024 and technology continues to advance. The TouchPad isn’t new by any means, but that doesn’t mean it can’t be slightly modernized to be more convenient today. Specifically, it is entirely possible to convert the TouchPad’s Micro USB port to USB C for charging and USB storage access. I’ll show you how.
      This is a tough mod which requires micro-soldering and modifying a PCB which you will have a hard time sourcing a replacement for without buying another TouchPad. Proceed at your own peril.
      Tools for the Job
      To do this mod you’ll need a few things for tools and parts. Here’s a list of what I used:
      – Needle nose pliers/tweezers
      – USB C boards with 5.1k resistors
      link hidden, please login to view
      – Soldering iron, solder, flux and a hot air station
      – Flush cuts
      – Dremel with cutting or sanding wheel
      – 28 AWG wire or smaller. 30 AWG is pretty good but any wire around 0.25mm to 0.5mm should work.
      – Small file and screwdriver set
      – Painter’s and kapton tape
      – Metal spudger Disassemble the TouchPad
      This is where you’re going to want to get that metal spudger out and be very careful not to snap clips. I can’t explain it better than iFixit already did so go check out their and then come back here.
      Modify the USB Connector Board by Removing the Micro Port
      There are a few ways to remove the Micro USB port. I added a bunch of flux and coated all the connectors in fresh leaded solder and then used a hot air station set to 800 degrees while wiggling the port very slightly with needle nose pliers. You don’t have to be particularly careful here so if you want to cut the port off with the dremel or the flush cuts or just rip it off with the pliers, (I don’t recommend it but…) that’s fine. We’re not using the pads it’s soldered to anyway. You should STILL be careful not to crack the board. Go slow. Be patient.
      Trim the USB C Board
      We need to expose the USB C port a bit on this board so let’s cut it down. Grab the painter’s tape and flip the USB C board upside down. You’ll see a small trace between the front and rear anchor points on the right side, which we don’t want to cut. Mark the tape just on the other side of that trace like I did. Dremel along the tape line until you get to the port. You can then use needle nose pliers, a flat file, and/or flush cuts to remove the rest of the board from the bottom of the port.
      Prepare the USB Connector Board for the USB C Port
      We need to slide the port into the old space so grab the painter’s tape again and mark off the area I marked to make room for the USB C port. You can place the port up to it like I did and use that as a guide. Grab your dremel again or a similar tool and cut out what you marked off. When you’re done, the USB C port should slide easily into the groove. It will fit tighter when we add the kapton tape in a later step.
      Make Room in the TouchPad for the Added Thickness of the USB C Board
      The USB C board will sit underneath the USB connector board so we have to make room by trimming away the plastic underneath. For this you’ll need to use flush cuts or any other tool you have to chip away. You could use the dremel for this if you’d like. Be careful to not go beyond the first inner layer. Beyond that is the outer shell of the TouchPad. There’s no real method here, just cut out the screw posts and chip away. Use the pictures below as a guide.
      Cut the USB C Hole from the Old Micro USB Hole
      To open the micro USB hole enough to fit the USB C port, take a rounded file to the left and right of both sides and just file a little bit at at time. Use a small flat file to widen the top and bottom of the port. This process is just trial and error. File a little and then grab the USB C board to test. The port will need to fit inside the hole a bit so you can push it through from the outside to test the hole size if that’s easier. Note: the USB C board will likely not rest on the bottom of the TouchPad and will float a little. This is good because it makes room for your wires and a little kapton tape underneath.
      Tape the USB C Board
      Since we hacked away at the USB connector board it’s possible we’ve provided the perfect environment for creating shorts! Oh no! So get out the kapton tape because we’re going to add a layer on both sides. You’ll see how I did it on one side below. Do it on both sides. You’ll also notice how I did not cover those two small square contacts just at the bottom of the tape. That’s because we need them.
      Where To Get Power and Data
      You’ll see the diagrams below which I’ve marked with VBUS (power), data in, data out, and ground. Obviously the old port is gone and most if its pads, but I wanted to show that both sides of the board have the connections. You could possibly do this mod differently, and if you so choose, hopefully these help.
      A quick note: this mod can be done with a 4-pin USB C port. That would give you power and data just like with the USB C board I’m using in this guide, however, a 4-pin USB C board will not charge with a USB C charger (ie USB 3.1). The board I’m using in this guide provides the ability to use any charger because it comes pre-built with 5.1k resistors wired to CC1 and CC2 to ground. This is the trick that tells the USB C chargers to send power to the device.
      Solder the USB C Board into the USB Connector Board
      This isn’t a “how to solder tutorial” so hit up youtube and find a good tutorial that works for you. In general though, use flux, pre-tin the VBUS, Ground, D-, and D+ pads on the USB C board as well as the points on the bottom of the USB connector board.
      Now for the tricky part, I didn’t list it in the Tools section above, but it would really help to have magnification or a digital microscope for this. I have these things and I used both. You might have steadier hands and better eyes than me. The picture below was my first attempt of the three TouchPads I modded, and it’s not my best soldering work, but fundamentally, this is what yours should look like.
      Put the Pieces Together
      You can use a bit of kapton tape to secure the wires in place a bit more if you’d like but it’s not required. It won’t short since it’s only plastic underneath. This is all press fit into place, but if you’re uncomfortable with that, you can add a little hot glue under the board as you put it back into the TouchPad. You don’t have to put the metal shield back into place if you don’t want to. It’s all a pretty tightly fit and if you find the TouchPad screen isn’t as flush as you want, just leave the metal shield off. A little kapton tape right on top would be fine instead.
      Congrats, You Now Have USB C
      I did this mod on three TouchPads and each one works fine with any USB charger I could find, including USB C port having USB 3.1 chargers. I can also confirm the data connection works just like it should to connect via USB mode on PC. Sadly, this doesn’t do anything to stop webOS from telling you the charger you’re using isn’t the original TouchPad barrel charger, but you can make a custom cable to stop that which I’ll cover in a future article on pivotCE.

      #webOS4ever

      The post first appeared on . Related posts:

    • By Flowace
      How do you measure your productivity? Are there specific metrics you use?
    • By News Reporter
      Home is where the heart is, and it’s also often the best place to start when you’re seeking to make a positive difference in the world. A prime example is the ‘home electrification’ trend, which, in a nutshell, helps drive sustainability by replacing fossil fuel-powered household appliances with cleaner and more efficient electricity-driven ones.

      Home electrification includes the installation of electric appliances and heating and cooling systems, such as heat pumps, which transfer heat from one place to another by circulating refrigerant. Heat pumps provide the practical benefits of year-round indoor comfort and lower utility bills. When integrated with solar panels and battery storage systems, they take things a step further – empowering homeowners with energy independence and the ability to power their homes during outages.


      According to a study published in the peer-reviewed scientific journal Joule, electrification could reduce greenhouse gas (GHG) emissions in the residential sector by 36 to 64 percent and cut overall GHG emissions in the U.S. by 5 to 9 percent.1 To accelerate the transition to electrification, many governments are now offering incentives and subsidies, such as those included in the U.S. government’s Inflation Reduction Act, to encourage the adoption of energy-efficient home technologies.2
      Electrifying your home with LG brings the compelling advantages of the company’s industry-leading core-tech and extensive lineup of sophisticated, energy-efficient products. LG’s innovative core components, including reliable, high-efficiency motors, ensure unparalleled performance and energy-savings across a variety of home appliances.

      The company also provides the seamless connectivity and easy energy management with ThinQ Energy, compatible with a comprehensive range of LG appliances and HVAC systems. The LG Home Energy Platform, centering on the Energy Storage System (ESS), optimizes energy usage to prevent waste and emissions, and enables smart control of connected home appliances.

      Many of LG’s products, which help reduce carbon emissions and enhance energy efficiency, are eligible for rebates. From ENERGY STAR® certified induction cooktops to low energy-consumption, low-emissions HVAC systems, LG offers a diverse array of cutting-edge solutions that can drastically decrease household reliance on fossil fuels and boost efficiency at the same time. Among these are water heaters equipped with heat pumps, and innovative laundry solutions like the impressive WashCombo washer-dryer with Inverter HeatPump.
      Embracing home electrification is an investment in a cleaner, healthier future. With LG’s energy-efficient appliances and core technologies, you can transform your living space into an all-electric abode – shrinking your energy footprint, minimizing your environmental impact and making a positive difference in the world.
      To learn more about LG’s solutions with energy efficiency for home electrification, stay tuned to
      link hidden, please login to view and . # # #
      1
      2

×
×
  • Create New...